This Ceramic Tiled Floor was in Penarth near Cardiff, the tile were 150 mm x 150 mm red dust pressed composition, known as versatile as it can be laid on both sides sometimes found around swimming pool areas due to their non-slip raised definition. The floor was looking a bit tired, so the customer asked if they could be revived. I did an inspection of the floor and noticed the grout was loose at the lounge doorway and this had to be re-grouted after my wet vacuum sucked it out part way through the cleaning process.
Cleaning Ceramic Tiles
First of all I tested for moisture which read very low, which was good news as it meant I was not going to have any issues with moisture in the tiles. I then applied masking tape to the skirting and carpet riser at the bottom of the staircase; I always protect these areas as once I removed a little paint on another customers skirting with Tile Doctor Remove and Go and so I deducted £50 .00 off the bill by way of compensation.
I then covered the floor with Tile Doctor Remove and Go let it soak in for half an hour, the floor was then rinsed twice and then to clean the grout I applied with Tile Doctor Pro-Clean which was then scrubbed into the grout joints; it was at this point some lose grout came away. The floor was rinsed twice again and I re-grouted the areas which needed it. The floor was dried with a wet vacuum and then it was left to dry for two days.
Sealing Ceramic Versatile Tiled Floor
On my return I checked the damp levels again before starting to seal the floor with three coats of Tile Doctor Seal and Go which also adds a nice shine to the tile. Caution should be applied to this type of tile as streak marks can be prominent when applying the sealer, in my experience I find as soon as the sealer is applied to the tile with a paint pad a cloth or any other method it marks the tile. It’s possible I’m just a being a perfectionist as the customer was thrilled with the finish.
As well as bathrooms and kitchens we also cover swimming pools which usually have a tiled pool surround and this was certainly the case with the photograph below which was taken at a property near the small market town of Sandy in Bedfordshire where the tile and grout around the pool had discoloured over time.
Cleaning Mosaic Pool Tiles
To clean the tiles we used a strong dilution of Tile Doctor Pro-Clean which left to soak into the tile and grout in sections before being scrubbed in using a stiff brush. You have to be careful with machinery around swimming poos as you don’t want any cleaning products draining into the swimming pool water.
The pro-clean and scrubbing action loosened the dirt and we were then able to use a Rotovac machine to finish the floor off and get the results you see above. The Rotovac which is also known as a Spinner tool is a really useful piece of equipment for a Tile Cleaner as it directs a jet of high pressure hot water onto the tile whilst simultaneously removing the water through a separate suction feature. The tool needs a lot of power so it runs from a high-pressure cleaning and extractor unit fitted into our van which can delivery water pressure between 500 and 3000 PSI. Another feature of the tool is the side skirts around the spinner head which along with the high suction prevent water from being splashed around making it ideal for this job.
These grubby looking Textured Ceramic Tiles were in a bathroom of a house in the old village of Narborough near Leicester. As you can see from the picture below they were overdue for a deep clean and the customer has been struggling to do that. On inspection it was clear that the textured surface which was designed to prevent slipping has become ingrained with dirt making them difficult to clean and therefore lose appearance. This can be a problem with a rough surface and so to prevent dirt building up the surface is sealed, however sealers do wear off after a few years depending on use and I suspect this is what happened here.
Cleaning and Preparing Porcelain Tile and Grout
To remove any remaining sealer from the less worn areas and clean the tile and grout a strong dilution of Tile Doctor Pro-Clean was applied and left to soak in to the surface for around ten minutes before scrubbing it into the tile with a rotary machine fitted with a black scrubbing pad and also a stiff hand brush along the grout lines. The floor was then rinsed down with fresh water which was removed with a wet Vacuum. This stripping and cleaning process was repeated until the tile and the grout was looking new again after which the floor was given a thorough rinse in order to remove any trace of product and then dried as much as possible using the wet vacuum.
Sealing Micro Porous Porcelain
We left the floor to dry and then came back two days later to seal the floor, testing it first with a damp meter to ensure it was dry. The two days was enough time to dry it out so we moved on to seal the floor using two coats of Tile Doctor Colour Grow which is an impregnating sealer that occupies the pores in the tile providing strong stain protection as well as lifting the colour.
I think you will agree the floor tile and grout look much cleaner and the new sealer will make it much easier to clean going forward.
This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the look without the expense.
Cleaning Ceramic Tile and Grout
We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning showers. The spray delivery is important as mixing the cleaning product with air makes it lighter and helps it cling to the tile and grout. The Oxy-Pro was left to soak into the tiles for around 15 minutes before being scrubbed into the tile and grout using a stiff grout brush. This action cleaned up the grout and tile nicely removing stains from shampoos and soaps etc.
Removing Mould from Grout
The grout was looking much improved but there was however some evidence of mould remaining which needed dealing with. To tackle this we used Tile Doctor Mould Away which is designed to remove mould off Silicone and Grout. It’s very easy to use, you simply spray the Silicone or Grout to be treated with Mould Away then leave to soak in for five minutes and then scrub with a brush and rinse with water repeating the process until the mould has disappeared.
It took a fair amount of manual effort but the results were well worth it as you can see.
A customer contacted us regarding a Ceramic Tiled Shower Cubicle problem they had with their house in Glasgow. The grout and mastic sealant had started to discolour and there was staining on both from mould which is quite a common problem in modern houses and our busy lifestyles and insulated homes with insufficient ventilation.
Cleaning Ceramic Tile and Grout
We started by giving the tiles a good scrub with Tile Doctor Pro-Clean then focusing on the grout we thoroughly scrubbed it with more Pro-Clean and a stiff grout brush, this process did well to clean up the tile and grout but unfortunately the grout had become too badly stained to be satisfactory. It’s a fact that the top layer of grout is actually porous and this is where the staining from the dyes in shampoos etc. will occur. The next step was to cut out all the old and mouldy mastic and seal around the shower using a sharp knife taking care not to scratch the shower tray.
To overcome the stained grout issue we gave the whole of the grout two coats of white Grout Colourant which is a very effective treatment that forms an epoxy barrier over the gout protecting it from future staining. Normally when you do this we recommend using a pre-treater product that provides a chemical key that allows the colourant to latch on to, in this case however I was happy that the scrubbing we gave the grout with Pro-Clean would have the same effect. The tiles were then wiped down using Tile Doctor Neutral Cleaner to remove any excess colourant from the tiles and give them a finishing shine. The last step was to Shower was finished off by applying new silicone sealant to the areas that were removed. The final result was a shower cubicle that looked recently installed. Source: Residential and Commercial Tile Cleaning in Glasgow
This fifty year old Ceramic tiled floor was installed in the communal parts of a small block of flats in Poole, Dorset. The tiles had not been given a deep clean in a long while and were now ingrained with dirt from many years of wear.
Cleaning Ceramic Floor Tile and Grout
To clean the tiles a strong dilution of Tile Doctor Pro-Clean was applied a left to soak into the tile for some time before working it into the floor using a rotary machine fitted with a black scrubbing pad. During this process it became clear that there was evidence that the tiles had been previously sealed using a metallised emulsion. This needed to be completely removed by buffing the floor and then steaming it; steaming also removed a myriad of paint spots that had accumulated over the years.
At this stage we took the opportunity to give the grout a good scrub with more Pro-Clean and a stiff hand brush before removing the cleaning solution with a wet vacuum and giving the entire floor a thorough rinse to remove and trace of cleaning product.
Sealing Ceramic Floor Tiles
The tiles were left to dry off overnight and we came back the next day to see if further work was needed. Now normally Ceramic tiles have a glazed surface that a sealer cannot take to however these tiles being were very old and the glaze had been worn off so sealed a small test are to see if it would take. The test was successful so I proceeded to seal the whole floor using Tile Doctor Colour Grow.
Due to the age of the tiles some were more faded than others which I could do nothing about however they looked generally clean and bright after restoration and the new Colour Grow sealer should provide protection for years to come.
The photograph below was taken in the kitchen of a residence in Bedford where the new owner wanted the Ceramic floor tiles deep cleaned before they moved in; you can see for yourself how dirty they had become.
Cleaning Ceramic Floor Tiles
To get the clean Ceramic tiles clean I applied a medium strength dilution of Tile Doctor Pro-Clean mixed 50/50 with NanoTech Ultra Clean with a mop; this was left to dwell on the surface of the tile for around twenty minutes. The next step was to then run over the floor using our high pressure Rotovac machine which applies and removes water at high pressure to remove the soil and rinse the floor at the same time. The Rotovac machines are an expensive investment but they do make Tile Cleaning easier, they are also flexible and can be used for carpet cleaning etc.
This Ceramic tiled bathroom with shower was installed at house Wilmslow and was overdue a refresh. You can see from the photographs below that the bathroom was looking tired and the tile and grout was discoloured with mould and acid build-up from washing products.
Cleaning Ceramic Tile and Grout
The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean which is a strong alkaline Tile and Grout cleaning product. The solution was decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry.
The grout looked better but I was unable to shift some of the staining so we decided to apply a white Grout Colourant, it’s a time consuming process but I think you will agree it made a big difference. Additionally the grout colourant product we use also forms a barrier over the surface making the grout much easier to clean going forward.
The last step was to remove the silicone sealant from along the top of bath and replace with new.
This Ceramic tiled family bathroom with shower was installed at house in Leighton Buzzard and was in need of rejuvenation. You can see from the photograph below that the tiles were in reasonable condition but the grout had become ingrained with dirt which is not unknown as the top layer of grout is porous and will discolour over time if not protected.
Cleaning Ceramic Tile and Grout
The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean mixed 50/50 with Nanotech Ultraclean which combines a highly powerful Tile and Grout cleaning product with tiny abrasive particles. For vertical tiled surfaces I recommend the mixture is decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry.
The grout was dried and the sealed with a couple of coats of Tile Doctor Grout Sealer which forms a protective barrier over the porous grout and keeps it looking good for longer. Most sealers can be used on grout (check the label to confirm) but for best results use a spray bottle as mixing the sealer with air improves its ability to stick to a vertical surface.
This Ceramic tiled bath with shower was installed at house in Didsbury, this customer wanted to give the bathroom a facelift and not usually it was the grout rather than the ceramic tile that had discoloured, the silicone also needed to be replaced due to the mould build-up and if you get mould on silicone it’s impossible to remove and can only be replaced. Unfortunately mould build-up in bathrooms is quite common in the UK due to our damp climate and modern insulated homes that restrict air flow. If you’re having this problem yourself consider installing a more powerful extractor fan or simply leaving the door to the bathroom open more often.
Cleaning Tile and Grout
The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean which is a highly recommended Tile and Grout cleaning product; being alkaline it’s safe to use on all sorts of tile and stone surfaces. For vertical tiled surfaces I recommend the mixture is decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry. If you’re doing this work yourself then you should know that Tile Doctor produces a product that comes with a spray attachment called Oxy Pro that is ready to use and can save you some time.
Whilst waiting for the tile and grout to dry the Silicone Sealer was removed using a sharp knife, as I mentioned before once mould gets a grip on silicone it will need to be replaced. It’s also worth mentioning at this point that silicone will last longer if the residue from soaps, shampoos and body washes etc. are rinsed away with clean water after having a shower as it’s the chemical and not the water that damages the silicone in the first place.
Cleaning the grout had made a visible difference and improved the overall look of the bathroom but it wasn’t showroom condition so to improve it further it was necessary to apply a white Grout Colourant. The product we use is epoxy based and forms a thin impermeable barrier over the grout so not only does it look good it protects the grout as well; it’s very easily applied using a small brush along the grout lines and you just wipe of the excess so it wasn’t long before the grout was looking like new.
Last step was to re-new the silicone sealant around the top of the bath and the job was finished; my customer was very pleased with the results and made the comment that she thought it looked like new.
This was a rather unusual request we were asked to look at in the Oxfordshire village of Long Hanborough; they had recently laid a new Tarmac drive and unfortunately it had been walked into the Ceramic tiled kitchen floor leaving a lot of dark staining. After failing to clean the tiles with various supermarket floor cleaners she called in Tile Doctor. Tile Doctor cleaning products are industrial strength so when I arrived I gave her a demonstration on a couple of tiles to show I could clean them and she was amazed at how easy I made it look and booked the work with me.
Removing Tarmac Stains from Ceramic Tiles
To resolve the problem I scrubbed the floor with Tile Doctor Grout Clean Up which is an acid based product designed to remove grout smears and mineral deposits. Ceramic tiles are very durable however being acid based you can’t leave it on the surface too long so the process was to quickly work it into the stain with a stiff bristle brush, rinse with water and then remove using a wet vacuum.
You can see the difference in the final photograph below where the dark staining has disappeared; the difference in tile colour was due to the lighting. The whole job was completed in one day and the customer was relieved that her floor was not ruined and left the comment below on the Tile Doctor feedback system.
He was thorough and excellent. Very grateful. M. Rawlings, Long Hanborough
The Ceramic floor tiles shown below were installed in a Luton high street restaurant, as you can see they were far from clean, deeply stained and even the grout had gone black.
Cleaning Ceramic Floor Tiles
Given the amount of dirt on the tile and grout we decided to apply a very strong combination of Tile Doctor Remove and Go mixed 50/50 with NanoTech Ultra Clean which results in the creation of a heavy duty stripper/cleaner containing nano sized abrasive particles that can penetrate deep into the dirt. The cleaning solution was left to dwell on the surface of the tile for twenty minutes before using a Rotovac machine which applies and removes water at high pressure to remove the dirt and rinse the floor.
Glazed ceramic tiles won’t take a sealer so once the entire floor was dry and stubborn areas re-done we were finished.
We were asked to clean these textured ceramic floor tiles in Wendover Bucks which had become heavily soiled and ingrained with dirt leaving the tiles with a black appearance, the grout lines had also become stained and discoloured. Our customer had tried all types of cleaning agents but could never get the desired effect.
Cleaning a Textured Ceramic Tiled Floor
A dilution of Tile Doctor Pro-Clean alkaline tile cleaner was applied throughout the tiled floor and worked in with the aid of a scrubbing pad fitted to a rotary machine, a stiff hand brush was also used along the grout lines and this managed to lift most of the soiling from the floor.
Next step was to use our powerful truck mounted heated turbo system which jet washed the remaining particles out of the crevasses of the stone. This system uses high pressure heated water though a spinner tool, it’s an amazing tool that returns the dirty water directly back to a recovery tank leaving the floor chemical free and neutralised.
These ceramic tiles situated in a large flat in Bravington Road W9 which is near Kensal Town in the City of Westminster, London. The tiles had been in place when the client moved into the flat some years ago and were badly in need of deep cleaning, attempts to remove the dirt using a steam cleaner had been successful but very slow. In the end the owner, realising that cleaning more than 75 square metres of tile herself in this way was going to take too long, decided to call in professional help from Tile Doctor.
Cleaning Ceramic Tiles
Using Tile Doctor Pro-Clean which is a heavy duty alkaline cleaning product and a medium brush on a Numatic buffing machine I lifted most of the ground-in dirt from the tiles before rinsing and scrubbing the floor again with a black buffing pad and scrubbing the grout clean by hand using a stiff grout brush.
I then thoroughly washed the floor with a mop and fresh water which was then removed with an aqua vacuum, this process was repeated until I was satisfied the floor was clean. When the floor was dry it revealed an nearly as-new ceramic tiled floor with a pleasing sandstone imitation design.
The photos show the floor before cleaning with a mark around where a piece of furniture had been removed and then the uniformly clean floor after the cleaning process was complete. The customer was delighted with the restored condition of her floor and amazed that it could have been made so clean.