Dealing with Mould in Ceramic Shower Cubicle

The photographs below are from the bathroom of a house in the Moston area of Manchester which is primarily residential and only 3 miles away from the city centre. My customer had been primarily concerned with the removal of unsightly mould but was also keen to have the grout in the ceramic tiled shower cubicle given a good deep clean.

Ceramic Tiled Shower Cubicle Before Restoration Moston Ceramic Tiled Shower Cubicle Before Restoration Moston

Cleaning a Ceramic Tiled Shower Cubicle

To clean the Shower Cubicle, I used a strong dilution of Tile Doctor Pro Clean which is a strong alkaline cleaner that works really well on grout. The Pro-Clean solution was decanted into a spray bottle and then sprayed onto the grout lines and left it to dwell. The air in the solution makes it lighter and easier for it to stick to vertical surfaces.

After a few minutes the Pro-Clean was scrubbed in using a stiff grout brush. The tiles were then rinsed with water to remove the soiled solution from the tiles and the process repeated where required.

Although cleaning process was a success there were still a few mould marks left so to tackle these I used Tile Doctor Mould Away spray using the same process of scrubbing and rinsing. The Mould Away spray did the trick for me and I moved on to remove the silicone around the shower cubicle. When removing silicone, you must make sure you get all mouldy silicone out otherwise it can spread from the old to the new.

Ceramic Tiled Shower Cubicle During Restoration Moston

After I had finished removing the silicone I tidied the shower cubicle and used a bit of gentle heat from my heat gun to dry the grout lines and edges where silicone used to be.

Grout Colouring a Ceramic Tiled Shower Cubicle

I used my damp tester to make ensure there was no dampness anywhere around the working area and then moved on to colouring the grout which would give the whole shower a fresh and consistent appearance. On this occasion, I used a White colour from the Tile Doctor range of Grout Colourant’s, it’s an epoxy based colourant that protects and rejuvenate the grout lines.

I had to use 2 coats of colourant to get the best result and then moved on to putting new silicone around the shower base with a high-quality mould resistant silicone. When finished adding fresh silicone I tidied up again and the job was complete.

Ceramic Tiled Shower Cubicle After Restoration Moston Ceramic Tiled Shower After Restoration Moston

I think you can’t argue the shower cubicle was transformed and customer even said it looks better then when it was new; we also fixed few chips for her whilst there and stripped and replaced the silicone around the sink as a bonus.

Ceramic Tiled Sink Grout Before Cleaning Moston Ceramic Tiled Sink After Cleaning Moston

 
 
Source: Ceramic Tile and Grout Cleaning Service in Manchester

Ceramic Bathroom Tiles Refreshed in Chessington

This bath with shower over was located at a rental property in the town of Chessington that had been recently vacated by students. I was called in by the landlord who was looking to re-rent the property. The request was to tidy up the ceramic tiles in the shower and bath area and to make it look decent again for the next batch of soap-dodgers. We often get asked to do end of tenancy tile cleans and have seen a lot worse than this one so I was confident it could be made to look like new again.

Dirty Ceramic Bath Tiles in Chessington before cleaning

The main problem was the grout had become darkened and stained from dirt and the dyes in soaps etc., the mastic sealant between the tile and the bath also needed replacing.

Cleaning Ceramic Tiled Shower Cubicle

To get the tile and grout clean I sprayed on Tile Doctor Oxy-Gel which works better than liquid products as being gel based it sticks to the wall tile and grout and really gets to work breaking down the dirt. I left this for a few minutes before scrubbing it in and then rinsing it off with water.

Whist this was drying I started to strip out the old mastic seal and tidied up the mess that had fallen into the bathtub using a vacuum.

Grout Colouring Shower Wall Tiles

With the tiles now clean and fresh grout dried the next step was to apply a White Grout Colourant to ensure all the grout had a consistent appearance. Although time consuming the grout colourant is easily applied with a small brush and then you wipe off any excess that gets onto the tile before it dries.

I left the grout colourant to dry for 30 minutes before applying another coat and once this had dried I set about adding a new mastic seal between the wall tile and bath. I always use a high quality silicone sealant for this; I never use cheap sealant as they soon discolour and can shrink resulting in water ingress problems.

Dirty Ceramic Bath Tiles in Chessington after cleaning

It takes a little time but the bathroom now looks much fresher and ready for the next tenants.
 
 
Source: Ceramic Tile and Grout Cleaning Service in West Surrey

Deep Cleaning an Edinburgh Shower Cubicle

This is a great example of the difference we can make to a Shower Cubicle which suffer from a build up of soap scum, mould and staining from the dyes in shampoos and soaps etc.

Ceramic Shower Cubicle Before Cleaning Edinburgh

This particular cubicle was installed at a property in the city of Edinburgh. The walls were Ceramic tiles which are ideal for shower areas as the glaze makes them completely water proof. However with grout being cementitious it does attract dirt and this shower was no different.

Ceramic Shower Cubicle Before Cleaning Edinburgh

Cleaning Ceramic Tiled Shower Cubicle

The first step was to remove the wire accessory holder and then soak all the tile and grout in a strong solution of Tile Doctor Pro-Clean. I find decanting into a spray bottle works best as it mixes it with air which makes it easier to stick to the wall.

With the Pro-Clean in place it was then hand scrubbed to get the tile and especially the grout clean of all the mould and other stains. The shower walls were rinsed down and the process repeated where necessary.

Grout Colouring Shower Wall Tiles

With the tiles and grout now clean we could see that the grout was still discoloured in some areas where it had been badly stained. One option at this point would be rake out the grout and replace with new however overtime it would only discolour again, so in agreement with the customer we applied a grout colourant in a Limestone colour to better match the tile.

The Grout Colourant would ensure all the grout had a consistent appearance while also adding an impenetrable barrier that will keep its appearance for a long time. It takes a little time to do but is easily applied with a small brush and then you wipe off any excess that gets onto the tile.

The next step was to strip out the mastic silicone sealant strip from around the base of the shower cubicle and replace with new. I used high quality silicone sealant that left nice lines and fresh look, don’t use cheap sealant as it will soon discolour and some have been known to shrink.

Ceramic Shower Cubicle After Cleaning Edinburgh

Deep cleaning and re-colouring the grout made a huge difference; the shower cubicle has been transformed and now looks like a new installation.

Ceramic Shower Cubicle After Cleaning Edinburgh

 
 
Source: Tile Cleaning Service in Edinburgh

Student Shower Cubicle Cleaining in East Sussex

We often get asked to do bathroom refresh and end of tenancy tile cleans however it’s a good job I’m not squeamish as this ceramic tiled shower cubicle was in a bad way.

Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux

The property was in the historic village of Herstmonceux in the Wealden District of East Sussex and apparently it had been leased to students who it seems were averse to cleaning, no surprise there.

Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux

Cleaning Ceramic Tiled Shower Cubicle

The first step was to remove the plastic product holder to expose the tile and grout, which revealed more staining and black mould.

Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux

With that removed I sprayed the Tile and Grout with Tile Doctor Oxy-Gel which works better than liquid products as being gel based it sticks to the wall tile and grout and really gets to work breaking down the dirt. I left this for a few minutes before scrubbing it and then rinsing it off with water. I had a problem with a patch of grout which was beyond cleaning and concerned it was going to upset the whole job I raked out it and applied new grout.

Grout Colouring Shower Wall Tiles

With the tiles now clean and fresh grout dried the next step was to apply a White Grout Colourant to ensure all the grout had a consistent appearance. Although time consuming the grout colourant is easily applied with a small brush and then you wipe off any excess that gets onto the tile.

The next step was to strip out the mastic silicone sealant strip from around the base of the shower cubicle and replace with new. I used high quality silicone sealant that left nice lines and fresh look, don’t use cheap sealant as it will soon discolour and some have been known to shrink.

Last step was to replace the plastic product holder which had been cleaned.

Ceramic Tiled Shower Cubicle After Cleaning Herstmonceux

Quite a difference I think you’ll agree. Future cleaning advice was left with the customer; I just hope he passes it onto the next tenant.

Ceramic Tiled Shower Cubicle After Cleaning Herstmonceux

 
 
Source: Ceramic Tile Cleaning & Refresh Service in East Sussex

Shower Cubicle Refresh in South Cumbria

Grange-over-Sands is a quaint little town on the Morecambe bay, roughly halfway between Barrow-in-Furness and Kendal in Cumbria. I was recently contacted by a property owner in the area who had heard about Tile Doctor services and was keen to have us restore their tiled shower cubicle which, as you can see from the photos below, had staining and mould on the ceramic tile, grout and silicone sealant.

Shower Cubicle in Grange-over-Sands Before Cleaning

The shower cubicle was looking far from inviting and well in need of a good deep clean. I agreed a quote for cleaning and recolouring of the grout, and was soon on my way to the property to carry out the work.

Shower Cubicle in Grange-over-Sands Before Cleaning

Cleaning and Recolouring a White Tiled Shower Cubicle

I started by cleaning the dirty grout with Tile Doctor Mould Away, which is a fast and effective formula for the removal of mould from silicone and grout. I sprayed the product onto the tile and grout and left it to soak in for five minutes, before scrubbing the area with a stiff brush. I then rinsed the area with water, and repeated the process until the mould and staining had completely disappeared.

To guarantee the overall appearance I had agreed with the owner to apply a grout colourant to the grout. For best results, we recommend a pre-treater is applied to the grout first as it helps bond the grout colour to the Grout. The pre-treater was applied then the whole cubicle was rinsed.

The next step was to carefully strip out the old silicone sealant from around the base of the cubicle using a sharp blade.

Colouring Grout in a Shower Cubicle

The grout needs to be dry to take the colourant so after cleaning and pre-treating I dried the grout with a heat gun on a low setting.

Once I was happy the grout was dry I started the recolouring process using a White colourant from the Tile Doctor range which has ten popular colours to choose from including Charcoal Grey, Cappuccino and Black. This would ensure the grout matched nicely with the rest of the cubicle.

The colourant not only restores the colour, it also rejuvenates and seals the grout joints. The lastly step was to apply fresh white silicone around the base of the cubicle.

Shower Cubicle in Grange-over-Sands After Cleaning

I think you will agree from the photos of the finished result the whole cubicle looks much fresher and that it would be difficult to tell the difference from a new installation.

Shower Cubicle in Grange-over-Sands After Cleaning

 
 
Source: Shower Tile and Grout Cleaning Service in Cumbria

Refreshing Bathroom Tile and Grout in Cheltenham

This Ceramic Tiled bathroom was at a house in the historic town of Cheltenham on the edge of the Cotswolds. As you can see from the photograph below the grout between the Ceramic tiles was very stained and had attracted black mould.

Bathroom Tiles Before Cleaning Cheltenham

Refreshing a Ceramic Tiles Bathroom

To get the tile and grout clean I sprayed on Tile Doctor Mould Away and left it to soak in for ten minutes before giving it a scrub with a stiff brush. The resultant slurry was rinsed off and then the process repeated once more.

The Mould Away made a difference to the tile and grout however the grout was still not 100% white, so I recommended applying a grout colourant which I was confident would have the desired effect.

Grout Colouring

Two coats of white Tile Doctor Grout Colourant were then applied; this product is basically painted on top of the existing grout with any excess wiped off the adjacent tile before it dries. It’s an epoxy based formula that becomes a long lasting barrier protecting the grout and also making it much easier to clean, it looks natural and I think you will agree it has made all the difference in fact the customer commented that it looks like a new bathroom.

Bathroom Tiles Before Cleaning Cheltenham

The job was completed in a day and I think you will agree the whole bath area now looks like a new installation.
 
 
Source: Ceramic Tile and Grout Cleaning and Restoration Service in Gloucestershire

Refreshing the Appearance of Shower Tile and Grout

Shower and bathroom mould and soap scum growth are probably the most common, annoying and frustrating tile-related problems. Wet and high humidity areas with poor ventilation provide the perfect breeding ground for mould and stains. Soap residue and body oils also create a food source for soap scum, mould to grow.

My customer in Dane Bank had the exact problem with dirty and mouldy grout lines in her shower cubicle. She had tried scrubbing the grout lines herself with a toothbrush and standard supermarket cleaners but never got the result she wanted.

Shower cubicle before refresh in Dane Bank

Fortunately she was lucky to find Tile Doctor from the internet and I was asked to pop over and take a look to see what could be done. I was confident we could make a big difference so I went through the options with her and give her price for the job. She was happy with the price and we agreed a date for me to return and complete the work.

Shower cubicle before refresh in Dane Bank

Cleaning a Ceramic Shower Cubicle

For grout lines cleaning I used Tile Doctor Grout Colorant Pre-Treat Cleaner, which successfully removes dirt, soil, soap scum and hard water deposits from grout joints. The product was sprayed on to the grout and left to dwell and seep into the pores for approximately five minutes to break down the soap scum and dirt before being scrubbed in using a stiff grout brush. The cleaning was successful but there were still few mouldy spots left. On these spots I used Tile Doctor Mould Away Spray that is meant for quick removal of mould from grout and silicone. One again product got sprayed on grout lines and left to dwell for five minutes and then scrubbed with stiff grout brush and then rinsed with clean water. After I had finished cleaning I express dried the tile and grout using high power heat gun.

Grout Colouring in a Shower Cubicle

With the area nice and dry, I had to choose the matching colour for the existing grout. There are ten colours to choose from the Tile Doctor range of Grout Colourant and on this occasion we chose Limestone as the best colour to match the tile.

Shower cubicle after refresh in Dane Bank

The colourant is easily applied directly to the grout and in this case I applied two coats. The product is epoxy based and completely seals and rejuvenates the appearance of the grout, which not only drastically improves appearance it also makes it much easier to clean in the future. After applying the re-colourant I buffed all grout colorant excess off the tiles and the shower cubicle was ready.

Shower cubicle after refresh in Dane Bank

My customer was very satisfied with the work and left the following comment on the Tile Doctor Feedback system

“Really, really happy with the service Tony provided and the recommendations he suggested. The work was carried out in a highly professional manner, to a high standard. I have already recommended him to friends. Thank you”
 
 
Source: Shower Tile Cleaning and Renovation Service in Greater Manchester

Restoring the Appearance of Bathroom Tiles

We commonly encounter customers who are struggling to keep their Ceramic tiled shower cubicles clean. Since most people use their showers every day, the tiles and grout inevitably come into contact with shampoos and soaps that can cause staining, discolouration and mould. In fact, it’s not uncommon for property owners to completely give up on trying to clean the tiles, especially as many everyday cleaners are ineffectual, and this allows the situation to worsen over time.

This customer, who lives in Hale Village – known to be one of the UK’s quietest and best kept villages despite being just outside the busy city of Liverpool – was fed up with the state of her tiled shower cubicle and decided to seek professional assistance. I explained that with regular maintenance using suitable products, the tiles could be easily kept clean. I visited the property to show her first hand the results that could be achieved by cleaning and recolouring the grout.

Ceramic bath tiles before refresh Hale Village Ceramic bath tiles before refresh Hale Village

Grout Cleaning and Recolouring Ceramic Bathroom Tiles

The ideal product for cleaning grout that has become affected by mould is Tile Doctor Mould Away, a fast and effective formula that can be directly applied. After applying the Mould Away I allowed it to soak into the grout for 20 minutes, before scrubbing it in with a special handheld brush. I also scrubbed it into the tiles to remove any excess staining caused by coming into contact with shampoos and soaps.

After completing a thorough clean of both the grout and tiles, it was time to remove the old silicone sealant from around the edges of the bath, and replace it with a fresh white sealant. I then opted to recolour the grout to match it with the tiles and the new sealant, doing so carefully with Tile Doctor’s own White Grout Colourant. This is just one of ten different Grout Colourant options we offer. Other options include Charcoal Grey, Black and Cappuccino Brown to much different colour tiles.

Ceramic bath tiles after refresh Hale Village Ceramic bath tiles after refresh Hale Village

The combination of cleaning and recolouring completely refreshed the appearance of this Ceramic tiled shower cubicle, to the point that it almost looks new. Needless to say my customer was very happy, and can see now just how easy it can be to keep these tiles looking good using the right products.
 
 
Source: Bathroom Tile and Grout Cleaning Service in Cheshire

Ceramic Tiled Kitchen Floor Refinished in Warrington

It can be amazing and equally frustrating just how quickly grout can become dirty and discoloured. I was recently contacted by a couple in Warrington to see if I could help them with their Ceramic tiled kitchen floor that had only been laid six months earlier. To their dismay, in that short time the grout had become discoloured and difficult to clean. They had given up trying to resolve the situation by themselves and so turned to Tile Doctor for some professional assistance.

Naturally I was happy to assist and so arranged to visit the property to conduct a small cleaning test where I demonstrated how with a combination of the right tools and products I could indeed get the grout lines clean again. Seeing the results of the test, the couple were more than happy to book me to complete the job.

Kitchen tiles before cleaning and grout recolour in Warrington

Grout Cleaning for Dirty Ceramic Tiles

On my return to the property, I repeated the same successful test clean across the entirety of the floor. This involved the application firstly of Tile Doctor Remove and Go, which is a strong cleaner, stripper and degreaser. I scrubbed the product thoroughly into all the grout lines, making sure I did not miss any dirt and stains.

I then started to clean the Ceramic floor tiles using our high alkaline cleaner, Tile Doctor Pro Clean. This was scrubbed into the floor in a similar fashion to the Remove and Go and then rinsed off with plain water extracting the waste water with a Wet Vat. The floor was left to dry over lunchtime.

Recolouring Grout for Ceramic Tiles

In the afternoon, I explained that whilst I could get the grout clean it was only a matter of time before it became dirty again. So, to provide a permanent solution I recommended to the customer that we apply an epoxy Grout Colourant, which adds a protective barrier over the grout. An alternative would have been to apply a Grout Sealer however this is best applied to new grout and in this case would not have guaranteed the uniform appearance required.

Before applying the Grout Colourant, I made sure the grout lines were dry by giving them a quick blast with a heat gun. I then started to colour the grout lines with our White Grout Colourant, which is part of a range made by Tile Doctor and is available in ten popular colours, including Black, Charcoal Grey and even Cappuccino Brown.

The difference made to the floor was quite remarkable. Not only is the grout now a uniform brilliant white, but it should remain so for a long time to come. You can see this yourself in the photograph below!

Kitchen tiles after cleaning and grout recolour in Warrington

 
 
Source: Tile and Grout Cleaning and Restoration Service in Cheshire

Refreshing the Appearance of a Ceramic Shower Cubicle

Shower cubicles can be the most difficult of tiled features to keep clean. Most are exposed to various acid-based soaps and shampoos on a daily basis, allowing mould and general muck to quickly build up along the grout lines and silicone. This leaves the entire area looking quite unappealing. In some cases, the grout lines become stained beyond a point where they can be restored to their original condition, so property owners will typically request to have the grout cut out and replaced however a faster and cheaper method is to have the grout completely recoloured.

Such was the case with this Ceramic tiled shower cubicle at a house in Wigan. It would take a lot to get the cubicle looking great again, having not been cleaned properly for a long time. The property owner decided to contact me for a professional refresh, including cleaning, new silicone sealer and recolouring of the grout.

Ceramic Shower Cubicle Before Refresh Wigan

Cleaning a Ceramic Tiles Shower Cubicle

I started the refresh by applying Tile Doctor Mould Away spray to the tiles and grout, and leaving it to dwell for an hour. As the name of the product suggests, Mould Away is a fast and effective cleaner for the removal of mould from silicone and grout, making it ideal for use on shower cubicles similar to this one. I then rinsed the entire area down with water before scrubbing the grout lines and tiles with a stiff grout brush to remove any remaining mould and lime scale, leaving them looking a lot cleaner.

Colouring Grout in a Ceramic Tiles Shower Cubicle

The cleaning process made a big improvement however the grout was still too stained so after removing the silicone strip from around the base of the shower I proceeded to recolour with our white Grout Colourant. The colourant is painted onto the grout and any excess is wiped of the tile before it dries which both improves the appearance of the grout and seals it in to protect it from further staining. The last step was to apply fresh white silicone along the base of the shower.

Ceramic Shower Cubicle After Refresh Wigan

The customer was very pleased with the refreshed appearance of their shower and you must admit it looks much more inviting now.
 
 
Source: Ceramic Tile Clearing and Restoration Service in Greater Manchester

Restoring the Appearance of Floor Tile Grout in Lancashire

Well maintained grout is fundamental to achieving a great looking tiled floor, whatever your choice of tile or stone. Even if the tiles themselves are in reasonably good condition, dirty and damaged grout lines can really upset the overall appearance of the floor.

Such was the case with this Ceramic Terracotta tiled floor in the bustling Lancashire town of Preston. The property owner recently had a new kitchen installed, but chose not to have new tiles fitted since the original tiles (dating back a good 15 years) were still in fantastic physical condition, with no chips or breaks. This is quite surprising considering that the kitchen is typically one of the main areas of traffic in any house however Ceramic and Porcelain tiles are very durable.

The grout, however, told a different story: it was very dirty and even missing in parts. Over the years it had come away and was replaced with new grout, however, this had left the whole floor with a displeasing patchy finish. Upon closer inspection it also became clear that the tiles themselves could do with a deep clean. I stepped in to discuss what could be done to improve the appearance of the floor and recommended a deep clean and grout colouring.

Grout Colouring Preston Before

Cleaning Ceramic Terracotta Tiles and Grout

Tile Doctor Pro Clean, a versatile high alkaline cleaner, was my choice of product for removing the dirt from the tiles. I applied it liberally across the floor before scrubbing it in with a scrubbing pad fitted to a rotary machine. Pro Clean is a go-to product for the removal of dirt, stains and other muck on most kinds of natural stone floor, and is capable of dealing with small amounts of soil to heavy buildup.

Once the tiles had been cleaned I turned special attention to the grout. I cleaned it with a product called Grout Colourant Pre-Treatment Cleaner, which is slightly acidic to break down ingrained dirt and tackle inherent grout smears, while ensuring that grout colourant bonds to the grout once it is applied.

Colouring Grout for Ceramic Terracotta a Tiles

The job took two days to complete as it was quite a large floor stretching into several rooms. The floor also needed to dry off overnight once I had completed the cleaning process, so I decided to call back the next day once it had dried completely. Upon my return I proceeded to colour the freshly cleaned grout by applying one coat of natural grey colourant. Sometimes two coats might be required for blending purposes, but not on this occasion.

The customer was very happy with the results. She had, in fact, thought of ripping up the old tiles as part of the kitchen restoration, but she decided not to since she really likes the tiles. A restoration by the Lancashire Tile Doctor was the appropriate and much less expensive choice!

Grout Colouring Preston After

 
 
Source: Ceramic Tile and Grout Cleaning Service in Lancashire

Refreshing the look of Ceramic Floor Tiles

Moving into a new home is a stressful but rewarding experience. This customer had just recently moved into a property in the neighbouring and historic Flintshire town of Mold, and was keen to make some renovations.

High on the agenda was the restoration of a large number of Ceramic floor tiles spread throughout multiple downstairs rooms. Although undecided as to whether to keep the tiles for the long-term or have them removed, the customer did resolve to have them professionally cleaned, especially since the previous owner had left the grout in a miserable state.

Ceramic Tiled Floor Before Cleaning in Mould

Upon initial inspection I noticed that the previous owner had attempted to put more grout on top of the existing one in some areas, the problem with this being that the two groups were of different colours. This left the grout looking inconsistent and dirtier than it actually was. I mentioned to the customer that I could re-colour the grout for them after cleaning the floor and that it would be the best solution in this situation.

Ceramic Tiled Floor Before Cleaning in Mould

Cleaning and Colouring Ceramic Tiled Floor Grout

As mentioned, the tiles themselves needed a deep clean, and so I set about applying a strong dilution of Tile Doctor Pro Clean liberally over the floor and leaving it to dwell for a short period. This allows the product, a high alkaline cleaner suitable for use on most natural stone floors, to seep into the pores of the stone to lift out and dissolve ingrained dirt and stains. Once I had allowed it to dwell I scrubbed the product into the tiles using a black pad fitted to a rotary machine.

Of course I also paid special attention to the grout lines, carefully cleaning them using more Pro Clean. With some floors I usually give the floor an acid wash at this with Tile Doctor Grout Clean Up to remove grout smears and mineral salt deposits but this was not necessary on this particular occasion.

Ceramic Tiled Floor After Cleaning in Mould

Once I had cleaned the entire floor I gave it a thorough rinse with water which was then extracted using a wet vacuum before leaving the floor to dry for two hours assisted with an air mover to speed up the process. When happy that the tiles were completely dry and ready to be re-coloured I went ahead and carefully applied a new black Grout Colourant that matched very well with the natural colour of the stone, giving the whole floor a smarter appearance.

Ceramic Tiled Floor After Cleaning in Mould

The customer was really pleased with the result and left some nice feedback on the job as a whole:

“Excellent experience all round, from initial consultation through to colour advice and scheduling work. Cannot speak highly enough of Joe, thoroughly professional and an amazing result. Highly recommended.”
 
 
Source: Ceramic Tile and Stone Cleaning and Sealing Service in Shropshire

Cleaning Grout in a Ceramic Tiled Shower Cubicle

To clean grout we normally recommend a good scrub with Tile Doctor Pro-Clean which is an strong alkaline product, in some cases however the staining cannot be removed completely and the only thing your can do with the exception of re-grouting is to re-colour the grout with a Grout Colourant which are available in ten popular colours.

In the case of this bathroom at a house in Paisley near Glasgow both the floor of the bathroom and the shower wall tiles were in need of a refresh and after a review of possible solutions is was agreed the easiest thing to do would be to re-colour the floor grout with a Light Grey colourant and the wall tiles with a White colourant.

Bathroom Floor Paisley Before Grout Colouring Shower Wall Tiles Paisley Before Grout Colouring

Cleaning and Colouring Grout

The first step before grout colouring is to give the grout a good scrub with Tile Doctor Pro-Clean to get it as clean as possible before applying the colourant. The grout was then rinsed and then dried ready for the colourant to be applied. You may be surprised to hear but we often find the biggest cause of staining to grout are the dyes contained in soaps and shampoos.

Once the grout is ready it’s a straightforward process of applying the colourant evenly along with thin coats along the grout line working the brush backwards and forwards whilst minimising the amount that gets on the tile. We were not changing the colour of the grout substantially so one coat of colourant was sufficient for both sets of tile.

With two colours being applied we were careful to ensure different brushes were used for each job to avoid any contamination and once the job was complete a damp pad was used to remove excess product from the tile surface.

Bathroom Floor Paisley After Grout Colouring Shower Wall Tiles Paisley After Grout Colouring

As you can see from the photographs the difference was immediate, the other advantage of the colourant is it forms a barrier over the grout protecting it from staining and making it easier to clean going forward.
 
 
Source: Tile and Grout Maintenance Services in Paisley

Refreshing Ceramic Bathroom Tiles

This bathtub with shower over was at a house in the village of Kilmacolm near Greenock. As you can see from the photograph below the grout was stained in places and a tile had become loose behind the taps due to a previous leak causing it to fall out.

Bathroom Refresh Before Kilmacolm

Refreshing a Ceramic Tiles Bathroom

The first job was to put the loose ceramic tile back on the wall, a process involving the scraping off the adhesive and grout from the wall and tile before re-fixing with fresh tile adhesive and the grouting. We placed a blanket in the bathtub during the work to protect it.

Next the tiles were given a wash down Tile Doctor Pro-Clean with particular attention paid to the grout by scrubbing it with a stiff brush. It was our intention to use a grout colourant on the grout and I wanted to ensure we had a good bond.

Whilst the tiles were drying I set about stripping off the old silicone sealant between the bath and the ceramic tiles wall, debris cleared and any remaining sealant was carefully scraped away and then replaced with new silicone.

Grout Colouring

Last step was to apply two coats of white Tile Doctor Grout Colourant, this product is basically painted on top of the existing grout with any excess wiped off the adjacent tile before it dries. It’s an epoxy based formula that becomes a long lasting barrier protecting the grout and also making it much easier to clean, it looks natural and combined with the new silicone it gave the whole bath surround a real uplift.

Bathroom in Kilmacolm After Refresh

The job was completed in a day and I think you will agree the whole bath area now looks like a new installation.
 
 
Source: Professional Tile, Stone and Grout cleaning services in Glasgow

Cleaning a Mouldy Shower Cubicle

A customer contacted us regarding a Ceramic Tiled Shower Cubicle problem they had with their house in Glasgow. The grout and mastic sealant had started to discolour and there was staining on both from mould which is quite a common problem in modern houses and our busy lifestyles and insulated homes with insufficient ventilation.

Cleaning Ceramic Tile and Grout

We started by giving the tiles a good scrub with Tile Doctor Pro-Clean then focusing on the grout we thoroughly scrubbed it with more Pro-Clean and a stiff grout brush, this process did well to clean up the tile and grout but unfortunately the grout had become too badly stained to be satisfactory. It’s a fact that the top layer of grout is actually porous and this is where the staining from the dyes in shampoos etc. will occur. The next step was to cut out all the old and mouldy mastic and seal around the shower using a sharp knife taking care not to scratch the shower tray.

Glasgow Ceramic Shower Refresh Before Cleaning Glasgow Ceramic Shower Refresh After Cleaning

Recolouring Grout

To overcome the stained grout issue we gave the whole of the grout two coats of white Grout Colourant which is a very effective treatment that forms an epoxy barrier over the gout protecting it from future staining. Normally when you do this we recommend using a pre-treater product that provides a chemical key that allows the colourant to latch on to, in this case however I was happy that the scrubbing we gave the grout with Pro-Clean would have the same effect. The tiles were then wiped down using Tile Doctor Neutral Cleaner to remove any excess colourant from the tiles and give them a finishing shine. The last step was to Shower was finished off by applying new silicone sealant to the areas that were removed. The final result was a shower cubicle that looked recently installed.     Source: Residential and Commercial Tile Cleaning in Glasgow